Delta Frequenzumrichtern

Delta 230V to 3x230V Frequency Controllers

Delta 230V to 3x230V Frequency Controllers These frequency controllers can be used to be able to run a 380V Mill or lathe using a 230V mains connection. Further one has full control over the frequency so especially with lathes its great to be able to set the rpm with just a dial of the potentiometer, instead of having to change gears. We offer a range of controllers between 750Watts and 2,2KW
VFD004E21T 1x220V->3x220V 0.4KW & Keypad
169.99Add to shopping cart (o. MwSt.)configurator
VFD007E21T 1x220V->3x220V 0.75KW & Keypad
179.99Add to shopping cart (o. MwSt.)configurator
VFD015E21A 1x220V->3x220V 1.5KW & Keypad
229.99Add to shopping cart (o. MwSt.)configurator
VFD022E21A 1x220V->3x220V 2.2KW & Keypad
279.99Add to shopping cart (o. MwSt.)configurator

Delta 120V to 3x230V Frequency Controllers

Delta 120V to 3x230V Frequency ControllersWe have this model in stock for our US based clients. Its a 110V input Model. It has a 110V input single phase and 3 phase 230V output. Perfect for using with our high speed TeknoMotors.
VFD007S11B 1x120V->3x220V 0.75KW
199.99Add to shopping cart (o. MwSt.)configurator

Delta DIN Rail mount MKE-DRA

Delta DIN Rail mount MKE-DRADiese Halter können die Delta VFD-E-Frequenz-Controller auf einer DIN-Schiene zu montieren. Es gibt zwei Modelle, die Typ A ist für die kleinen Modelle bis 750W. Das The B ist für den größeren Modellen.
Type A (72mm wide) MKE-DRA
4.99Add to shopping cart (o. MwSt.)

Delta DIN Rail mount MKE-DRB

Delta DIN Rail mount MKE-DRBThese mounts can be used to mount the Delta VFD-E frequency controllers on a DIN rail. There are two models, the type A is for the the small models up to 750w. The The B is for the larger models.
Type B (100mm wide) MKE-DRB
8.99Add to shopping cart (o. MwSt.)

Delta 400V Frequency Controllers

Delta 400V Frequency Controllers These frequency controllers can be used to be able to run a 380V Mill or Lathe using a 400V mains connection. One has full control over the frequency so especially with lathes its great to be able to set the rpm with just a dial of the potentiometer, instead of having to change gears.
VFD007E43T 400v->400V 0.7KW & Keypad
264.99Add to shopping cart (o. MwSt.)configurator
VFD015E43T 400v->400V 1.5KW & Keypad
264.99Add to shopping cart (o. MwSt.)configurator
VFD022E43A 400v->400V 2.2KW & Keypad
329.99Add to shopping cart (o. MwSt.)configurator
VFD037E43A 400v->400V 3.7KW & Keypad
435.99Add to shopping cart (o. MwSt.)configurator
VFD055E43A 400v->400V 5.5KW & Keypad
549.99Add to shopping cart (o. MwSt.)configurator
VFD075E43A 400v->400V 7.5KW & Keypad
614.99Add to shopping cart (o. MwSt.)configurator
VFD110E43A 400v->400V 11.0KW & Keypad
699.99Add to shopping cart (o. MwSt.)configurator
VFD150E43A 400v->400V 15.0KW & Keypad
949.99Add to shopping cart (o. MwSt.)configurator
VFD185E43A 400v->400V 18.5KW & Keypad
1,099.99Add to shopping cart (o. MwSt.)configurator
VFD220E43A 400v->400V 22.0KW & Keypad
1,219.99Add to shopping cart (o. MwSt.)configurator

Delta Brake Resistors

Delta Brake ResistorsWhen using a VFD in combination with for example a lathe, if you wish to slow down the main spindel at a fast rate. Then this brake resistor is required. It turns the mechanical energy into heat. Also for safety we recommend it. Some motors can take 10-20 seconds to slow down. If anything happens, you are always too late then. With the brake resistor its decreased to about 1 second...
Brake Resistor 100Ohm 150W (220V models)
30.99Add to shopping cart (o. MwSt.)
Brake Resistor 400Ohm 150W (400V models)
30.99Add to shopping cart (o. MwSt.)

Delta High Frequency Controllers

Delta High Frequency ControllersIn most case we sell a VFD-E in combination with a TeknoMotor. Some high speed milling motors need more than 600hz output frequency (maximum of the VFD-E), in that case we advise to use the Delta C200 VFD. It has a maximum output frequency of 2000 hertz. For that reason its perfect to be used in combination with high speed milling motors like the Jager or ELTE.
VFD022CB21A-21 1x220V->3x220V 2.2KW
349.99Add to shopping cart (o. MwSt.)
VFD022CB43A-21 400V->400V 2.2KW
389.99Add to shopping cart (o. MwSt.)
VFD037CB43A-21 400V->400V 3.7KW
459.99Add to shopping cart (o. MwSt.)

Delta High Power Brake Resistors

Delta High Power Brake ResistorsWhen using a VFD in combination with for example a lathe, if you wish to slow down the main spindel at a fast rate. Then this brake resistor is required. It turns the mechanical energy into heat. Also for safety we recommend it. Some motors can take 10-20 seconds to slow down. If anything happens, you are always too late then. With the brake resistor its decreased to about 1 second...
Brake Resistor 100Ohm 500W (400V models)
59.99Add to shopping cart (o. MwSt.)
Brake Resistor 75Ohm 1.0KW (400V models)
159.99Add to shopping cart (o. MwSt.)

USB-->>RS485 converter

USB-->>RS485 converter Der USB zu RS485 von Delta können mehrere Delta-Geräte PROGAM werden. Wir Mosten oft nutzen sie für die VFD-E frequentie Controller. Sie kann aber auch verwendet, um den Delta PLC programmieren.
USB->>RS485 Converter (IFD6500)
49.99Add to shopping cart (o. MwSt.)

Delta Keypad

Delta Keypad Bei Verwendung eines VFD-E-Typ-Frequenz-Controller von Delta. Es ist möglich, die Tastatur zu entfernen. Wir haben immer eine Tastatur mit den VFD, aber wenn Sie aus irgendeinem Grund eine zusätzliche Tastatur benötigen oder wenn Sie Ihr verloren haben. Wir bieten es hier als Ersatzteil
Keypad VFD-E (KPE-LE02)
14.99Add to shopping cart (o. MwSt.)

Delta Keypad Extension Cables EG

Delta Keypad Extension Cables EGKeypad Extension Cables: To meet the growing application needs of our customers, Delta provides an affordable and convenient cable assembly in three sizes that allows the user to extend the access to the drive’s standard keypad up to 5 meters. Supporting the VFD-B, VFD-M, VFD-F and VFD-E standard keypads only.
Delta Keypad Extension Cables EG1010A 1 meter
19.99 (o. MwSt.)
Delta Keypad Extension Cables EG3010A 3 meter
26.99 (o. MwSt.)
Delta Keypad Extension Cables EG5010A 5 meter
34.99 (o. MwSt.)

Cable DCNC-RTR to Delta VFD

Cable DCNC-RTR to Delta VFD Unsere RTR Performance CNC-Steuerung verfügt über eine integrierte Schnittstelle zum Anschluss eines VFD. Mit diesem Kabel wird die Verbindung zu einem Delta VFD sehr leicht gemacht. Es lässt sich direkt an den Controller, und nur sehr einfache Verdrahtung muss auf dem VFD-Seite erfolgen. Für die wir Dokumenation.
Cable DCNC-RTR to Delta VFD 1 meter
23.99Add to shopping cart (o. MwSt.)
Cable DCNC-RTR to Delta VFD 3 meter
29.99Add to shopping cart (o. MwSt.)

Configurator