Vis à billes ISEL 25mm

25mm Ballscrews No End machining

25mm Ballscrews No End machiningWhat is offered is just the bare ballscrew. No end machining included. If you would like also end machining: Order the total spindle length you need here and order separate the standard or custom end machining. WARNING: Above 1500mm length we cannot guarantee correct balancing/run-out of the machined ends.
25mm pitch 5mm price per meter€ 76.99 p/m (sans TVA)
€ 2.00 p/cut (sans TVA)
mm (min: 100mm, max: 3000mm)

configurator
25mm pitch 10mm price per meter€ 76.99 p/m (sans TVA)
€ 2.00 p/cut (sans TVA)
mm (min: 100mm, max: 3000mm)

configurator
25mm pitch 20mm price per meter€ 76.99 p/m (sans TVA)
€ 2.00 p/cut (sans TVA)
mm (min: 100mm, max: 3000mm)

configurator

25mm Standard End Machining

25mm Standard End Machining We can do the end machining of ballscrew since we have a CNC lathe in our shop. We only offer the 2 Sided ISEL standard CNC machining. The spindel will then fit into all the parts bearing etc we sell. When you need only slight changes to this design, we can help you out as well. However, we do not make custom designs.
25mm Standard End Machining
129.99Add to shopping cart (sans TVA)configurator

BK/FK + BF/FF 15 End Machining

BK/FK + BF/FF 15 End Machining
129.99Add to shopping cart (sans TVA)

25mm Ballnuts Variant 3

25mm Ballnuts Variant 3For the 25mm Ballscrew system ISEL only has the Variant 3 type of nut. It needs to be used in combination with the MountingBlocks. Since these provide the pre tension on the system. 5mm/10mm and 20mm pitch is available, use the higher pitches for longer spindels, this will allow the rpm of the spindel to be less as the same feedrate.
25mm Variant 3 pitch 5mm 213 700 0005
85.99Add to shopping cart (sans TVA)configurator
25mm Variant 3 pitch 10mm 213 700 0010
96.99Add to shopping cart (sans TVA)configurator
25mm Variant 3 pitch 20mm 213 700 0020
104.99Add to shopping cart (sans TVA)configurator

Wipers for 25mm ISEL Ballscrew

Wiper (set of 2 pieces) 213700 9000
8.99Add to shopping cart (sans TVA)

ISEL SpannBlock 1 for 25mmØ 5-10mm pitch Square Flange

ISEL SpannBlock 1 for 25mmØ 5-10mm pitch Square FlangeSquare Flange Housing for 25mm Ballnuts Variant 3.
25mm 5/10mm pitch SpannBlock 1 Square Flange (213 700 9001)
63.99Add to shopping cart (sans TVA)

ISEL SpannBlock 1 for 25mmØ 20mm pitch Square Flange

25mm 20mm pitch SpannBlock 1 Square Flange (213 700 9002)
75.99Add to shopping cart (sans TVA)

Round Flange Housing

Round Flange HousingRound Flange Housing for 25mm Ballnuts Variant 3.
5/10mm pitch SpannBlock 2 Round Flange
63.99Add to shopping cart (sans TVA)
20mm pitch SpannBlock 2 Round Flange
82.99Add to shopping cart (sans TVA)

Locking Nuts and Wrenches

Locking Nuts and WrenchesThese locking nuts are often used with ballscrews. The end machining for the 16mm ISEL spindels requires the m10x0.75 nut, for the ISEL 25mm requires m17x1 nut. The fine thread of 1mm makes it easier to adjust the pretension on the ball bearings. That's why these type of nuts are used, and not normal type of thread.
m12x1 Locking Nut
5.00 (sans TVA)
m16x1 Locking Nut
5.00 (sans TVA)
m17x1 Locking Nut
5.00 (sans TVA)
m20x1 Locking Nut
5.00 (sans TVA)
Wrench for m12x1 Locking nut
9.20 (sans TVA)
Wrench for m17x1 Locking nut
9.20 (sans TVA)

Configurator