ISEL Kogelomloopspindels 25mm

25mm Diameter 5mm Pitch Ballscrew (NO END MACHINING!)

25mm Diameter 5mm Pitch Ballscrew (NO END MACHINING!) Wat we hier aanbieden is enkel de spindel nog zonder eindbewerking. Als u ook de eindbewerking wil hebben dan moet u deze los bestellen. Wat u dus doet, is hier de totaal lengte van de spindel bestellen en dan los de eindbewerking bestellen.
25mm Diameter 5mm Pitch Ballscrew (NO END MACHINING) € 76.99 p/m (excl. btw)
€ 2.00 p/cut (excl. btw)
mm (min: 100mm, max: 3000mm)

configurator

25mm Diameter 10mm Pitch Ballscrew (NO END MACHINING!)

25mm Diameter 10mm Pitch Ballscrew (NO END MACHINING!) What is offered is just the bare ballscrew. No end machining included. If you would like also end machining: Order the total spindle length you need here and order separate the standard or custom end machining. WARNING: Above 1500mm length we cannot guarantee correct balancing/run-out of the machined ends.
25mm pitch 10mm price per meter€ 76.99 p/m (excl. btw)
€ 2.00 p/cut (excl. btw)
mm (min: 100mm, max: 3000mm)

configurator

25mm Diameter 20mm Pitch Ballscrew (NO END MACHINING!)

25mm Diameter 20mm Pitch Ballscrew (NO END MACHINING!)What is offered is just the bare ballscrew. No end machining included. If you would like also end machining: Order the total spindle length you need here and order separate the standard or custom end machining. WARNING: Above 1500mm length we cannot guarantee correct balancing/run-out of the machined ends.
25mm Diameter 20mm Pitch Ballscrew (NO END MACHINING)€ 76.99 p/m (excl. btw)
€ 2.00 p/cut (excl. btw)
mm (min: 100mm, max: 3000mm)

configurator

25mm Standard End Machining

25mm Standard End Machining We can do the end machining of ballscrew since we have a CNC lathe in our shop. We only offer the 2 Sided ISEL standard CNC machining. The spindel will then fit into all the parts bearing etc we sell. When you need only slight changes to this design, we can help you out as well. However, we do not make custom designs.
25mm Standard End Machining
129.99Toevoegen aan mandje (excl. btw)configurator

BK/FK + BF/FF 15 End Machining

BK/FK + BF/FF 15 End Machining
129.99Toevoegen aan mandje (excl. btw)

ISEL 25mm Ballnut Variant 3 pitch 5mm (213 700 0005)

ISEL 25mm Ballnut Variant 3 pitch 5mm (213 700 0005) ISEL heeft voor het 25mm kogelomloop segment enkel de Variant 3 moer beschikbaar. Deze is enkel te gebruiken in combinatie met de montage blokken. Deze zorgen voor de voorspanning op de spindel. 5mm/10mm en 20mm spoed zijn er verkrijgbaar, gebruik voor lange lengtes spindels, de hogere spoed om het toerental van de spindel beperkt te houden en toch de juiste voeding snelheid te verkrijgen.
ISEL 25mm Ballnut Variant 3 pitch 5mm (213 700 0005)
85.99Toevoegen aan mandje (excl. btw)configurator

ISEL 25mm Ballnut Variant 3 pitch 10mm (213 700 0010)

 ISEL 25mm Ballnut Variant 3 pitch 10mm (213 700 0010)For the 25mm Ballscrew system ISEL only has the Variant 3 type of nut. What we offer here is the 10mm Pitch model. It needs to be used in combination with the MountingBlocks. Since these provide the pre tension on the system. 5mm/10mm and 20mm pitch is available, use the higher pitches for longer spindels, this will allow the rpm of the spindel to be less as the same feedrate.
25mm Variant 3 pitch 10mm 213 700 0010
96.99Toevoegen aan mandje (excl. btw)configurator

ISEL 25mm Ballnut Variant 3 pitch 20mm (213 700 0020)

ISEL 25mm Ballnut Variant 3 pitch 20mm (213 700 0020)For the 25mm Ballscrew system ISEL only has the Variant 3 type of nut. What we offer here is the 20mm Pitch model. It needs to be used in combination with the MountingBlocks. Since these provide the pre tension on the system. 5mm/10mm and 20mm pitch is available, use the higher pitches for longer spindels, this will allow the rpm of the spindel to be less as the same feedrate.
ISEL 25mm Ballnut Variant 3 pitch 20mm (213 700 0020)
104.99Toevoegen aan mandje (excl. btw)configurator

Wipers for 25mm ISEL Ballscrew

Wiper (set of 2 pieces) 213700 9000
8.99Toevoegen aan mandje (excl. btw)

ISEL SpannBlock 1 for 25mmØ 5-10mm pitch Square Flange

ISEL SpannBlock 1 for 25mmØ 5-10mm pitch Square FlangeRechthoekig Spannblock met voor 25mm Ballnuts Variant 3.
25mm 5/10mm pitch SpannBlock 1 Square Flange (213 700 9001)
63.99Toevoegen aan mandje (excl. btw)

ISEL SpannBlock 1 for 25mmØ 20mm pitch Square Flange

25mm 20mm pitch SpannBlock 1 Square Flange (213 700 9002)
75.99Toevoegen aan mandje (excl. btw)

ISEL SpannBlock 2 for 25mmØ 5-10mm pitch Round Flange

ISEL SpannBlock 2 for 25mmØ 5-10mm pitch Round FlangeSpannblock met ronde flens voor 25mm Ballnuts Variant 3.
ISEL SpannBlock 2 for 25mm 5-10mm pitch Round Flange
63.99Toevoegen aan mandje (excl. btw)

20mm pitch SpannBlock 2 Round Flange

20mm pitch SpannBlock 2 Round Flange
82.99Toevoegen aan mandje (excl. btw)

Wrench for GUK 01 m12x1 Locking nuts

Wrench for GUK 01 m12x1 Locking nutsThese locking nuts are often used with ballscrews. The end machining for the 16mm ISEL spindels requires the m10x0.75 nut, for the ISEL 25mm requires m17x1 nut. The fine thread of 1mm makes it easier to adjust the pretension on the ball bearings. That's why these type of nuts are used, and not normal type of thread.
Wrench for m12x1 Locking nut
9.20 (excl. btw)

Wrench for GUK 03 m17x1 Locking Nuts

Wrench for GUK 03 m17x1 Locking NutsThese locking nuts are often used with ballscrews. The end machining for the 16mm ISEL spindels requires the m10x0.75 nut, for the ISEL 25mm requires m17x1 nut. The fine thread of 1mm makes it easier to adjust the pretension on the ball bearings. That's why these type of nuts are used, and not normal type of thread.
Wrench for m17x1 Locking nut
9.20 (excl. btw)

GUK 01 M12 x 1.00 Nylon Insert Locking Nuts

GUK 01 M12 x 1.00 Nylon Insert Locking Nuts These locking nuts are often used with ballscrews. The end machining for the 16mm ISEL spindels requires the m10x0.75 nut, for the ISEL 25mm requires m17x1 nut. The fine thread of 1mm makes it easier to adjust the pretension on the ball bearings. That's why these type of nuts are used, and not normal type of thread.
m12x1 Locking Nut
5.00 (excl. btw)

GUA 01 M16 x 1.00 Nylon Insert Locking Nuts

GUA 01 M16 x 1.00 Nylon Insert Locking NutsThese locking nuts are often used to repair m17x1 thread. When the thread is damaged beyond repair, its possible to machine down the spindel to m16x1. Then this nut replaced the normal m17x1 thread .ISEL 25mm normally requires m17x1 nut. The fine thread of 1mm makes it easier to adjust the pretension on the ball bearings. That's why these type of nuts are used, and not normal type of thread.
GUA 01 M16 x 1.00 Nylon Insert Locking Nuts
5.00 (excl. btw)

GUK 03 M17 x 1.00 Nylon Insert Locking Nuts

GUK 03 M17 x 1.00 Nylon Insert Locking NutsThese locking nuts are often used with ballscrews. The end machining for the 16mm ISEL spindels requires the m10x0.75 nut, for the ISEL 25mm requires m17x1 nut. The fine thread of 1mm makes it easier to adjust the pretension on the ball bearings. That's why these type of nuts are used, and not normal type of thread.
m17x1 Locking Nut
5.00 (excl. btw)

GUK 04 M20 x 1.00 Nylon Insert Locking Nuts

GUK 04 M20 x 1.00 Nylon Insert Locking NutsThese locking nuts are often used with ballscrews. The end machining for the 16mm ISEL spindels requires the m10x0.75 nut, for the ISEL 25mm requires m17x1 nut. The fine thread of 1mm makes it easier to adjust the pretension on the ball bearings. That's why these type of nuts are used, and not normal type of thread...
GUK 04 M20 x 1.00 Nylon Insert Locking Nuts
5.00 (excl. btw)

Configurator